Virsun Organic India Private Limited
Virsun Organic India Private Limited
Kherado, Alwar, Rajasthan
SEND SMS
SEND EMAIL

AAC BLOCK ADHESIVE

Our product range includes a wide range of aac block adhesive block bonding adhesive&jointing mortar for aac blocks.

AAC BLOCK ADHESIVE block bonding adhesive&jointing mortar for aac blocks

AAC BLOCK ADHESIVE block bonding adhesive&jointing mortar for aac blocks
  • AAC BLOCK ADHESIVE block bonding adhesive&jointing mortar for aac blocks
  • AAC BLOCK ADHESIVE block bonding adhesive&jointing mortar for aac blocks
  • AAC BLOCK ADHESIVE block bonding adhesive&jointing mortar for aac blocks
Get Best Quote
Approx. Price: Rs 240 / BagGet Latest Price

Product Details:

Minimum Order Quantity100 Bag
Coverage Areaapplied at 3mm thickness is approximately 2.5 Sft per Kg
Surface of ApplicationBLOCK ADHESIVE,AAC BLOCK ADHESIVE JOINTING MORTAR&BLOCK BINDING ADHESIVE,BLOCK ADHESIVE,AAC BLOCK ADHESIVE JOINTING MORTAR&BLOCK BINDING ADHESIVE,BLOCK ADHESIVE,AAC BLOCK ADHESIVE JOINTING MORTAR&BLOCK BINDING ADHESIVE,AAC BLOCK ADHESIVE JOINTING MORTAR&BLOCK BINDING ADHESIVE
For Use inSide Walls
BrandSUN BLOCK
Brick/Block ColorGRY
FormPowder
Packaging Size40 kg
Packing Type40KG
Block TypeALL
Coverageapplied at 3mm thickness is approximately 2.5 Sft per Kg
ConditionNew
Weight40 KG
Shelf LifeFactory sealed bags of this product are guaranteed to be of first quality for one 1 year if store
ColorGrey
Grade StandardBLOCK ADHESIVE& JOINTING MORTAR
Pot Life1 Hour
SizeALL

AAC BlocK ADHESIVE AAC BLOCK ADHESIVE MANUFATURE is a factory prepared blend of carefully selected raw materials, portland cement and graded aggregates and polymers. Designed for use with water to produce high strength thixotropic mortar, for laying aerated lightweight concrete, fly ash bricks, cement hollow blocks, cellular concrete blocks or smoothing over the block work surface in layers of up to 12mm thickness, that meet and exceed the requirements of National and International Approximately 200 sq.ft. per 50 kg bag when used at 2-3mm bed thickness Coverage is based on smoothness and evenness of the substrate, size of blocks used and the thickness of mortar used.

Surface Preparation

If a plaster/leveling mortar bed is applied, ensure that it is cured for at least 7 days to achieve proper strength before application of adhesive for construction of block work.

Ensure the substrate is clean and free from impurities like dust, dirt, debris, oil, grease, curing agents, existing paints, loose plaster etc.

Mixing The product can be mixed by hand Pour water in a clean container and then add the powder SUN Block adhesive until the mixture becomes creamy and plastic. Leave the mix to slake for 5-10 min and remix before use. Mix only sufficient quantity of adhesive for the immediate need.

Proportion

Approximately 1 bag of 20 to 50 Kg of VIRSUN SUN Block Adhesive with 12 to 15 liters of Water. Adjust the quantity of liquid to obtain proper consistency.

Applications

Thin bed mortar for laying blocks Before placing mortar, ensure the block work to be dry and surfaces cleaned properly. Place the mixed mortar on the block work In thin layers of 2 to 3 mm (or as required by engineers at the site) using ta rowel and place the next layer of blocks on the mortar. Keep Joints between the blocks as required by the site engineers and fill the Joints with the mixed mortar, using a trowel. Check the plumb of the wall while laying the blocks to keep the walls perfectly vertical to the plumb.

Smoothing over the block work Before placing mixed mortar, apply a bonding layer of 1 to 2mm thick SUN Block Adhesive mortar using a trowel pressing down on the block work. Then apply SUN Block Adhesive at a thickness of 8 to 10mm and smoothen using a sponge or rubber / wooden float. When installing large blocks, spread higher thickness of SUN Block adhesive. Select proper type of notched trowel.

As Adhesive to install tiles SUN Block Adhesive can be used as a thin-set adhesive to Install tiles on SUN Block/Fly ash brick walls. Use a suitable notch trowel to achieve the desired thickness of adhesive for installation of tiles on the wall. The most Important standard to keep in mind Is to ensure that the piece of block Is completely bedded In the mortar or adhesive with 100% coverage after Beat In.


Installation

Wet the surface and remove the excess water before applying the adhesive. Ensure the area Is shaded from sunlight. The adhesive shall be applied with the flat side of the trowel using a scraping motion to work the material into good contact with the surface to be covered. Additional mortar is then applied with the notched edge of the trowel.


EXPANSION AND CONTROL JOINTS

All slabs must be plumb and true to within '/4" (6mm) in 10 ft (3m). Follow ANSI Specification AN-3.8 'Requirements for Expansion Joints' or Detail EJ 171 'Expansion Joints'. Do not cover expansion joints with mortar.

Existing joints in concrete must be carried through tile work and shall confirm to architectural details.

It shall be spaced at 5m X 5m and shall conform to architectural details.

Request
Callback


Additional Information:

  • Production Capacity: 3000 matric ton par month
  • Delivery Time: ORDER AFTER 3 DAYS
  • Packaging Details: 40 KG BAG
Yes! I am Interested
View PDF
X

Explore more products



Reach Us
Rajender Sharma Sharma (Director)
Old Delhi Road
Kherado, Alwar- 301001, Rajasthan, India



Call Us

Share Us

F GT L


Send E-mailSend SMS