Minimum Order Quantity: 50 Bag
|Model Number||IS:15477 TYPE 1 ISI STANDARD|
|Packaging Size||20 Kg|
|Surface Of Application||FLOOR AND WALL|
|Coverage||55 TO 60 FIT|
|Open Time||45 MINTAUE|
|Fixture Time||12 HOURS|
|Curing Time||12 HOURS|
Substrate: The surface to be covered with Ceramic tile shall be sound and confirm to good design, rigid, clean and free of dirt, oil, grease, curing compounds, form release agents or loose plaster and paint. For economy the surfaces should be level and true with in: Walls – 3mm in 2.5m Floors – 1.5mm in 1.0m Surface Preparation:
If a plaster/leveling mortar bed is applied, ensure that it is cured for at least 7 days to achieve proper strength before application of tile adhesive for installation of tile
Ensure the substrate is clean and free from impurities like dust, dirt, debris, oil, grease, curing agents, loose plaster etc
Dampen the wall before application of thin set adhesive
Clean the back of tile for any dust or coating
Mixing: The products can be mixed by hand or slow speed electric drill mixer (less than 300 rpm). Pour potable clean water in a clean container and then add the powder VIRSUN PLATINUM and mix until the mixture becomes creamy and plastic. Do not over mix. Leave the mix to slake for 5-10 min and remix before use. Mix only sufficient quantity of adhesive for immediate need. Proportion: Approximately 1 bag of VIRSUN PLATINUM with 5-6 ltrs of water. Adjust quantity of liquid to obtain proper consistency. Installation:
Wet the surface and remove the excess water before applying the adhesive. Ensure the area is shaded from sunlight. The adhesive shall be applied with the flat side of the trowel using a scraping motion to work the material into good contact with the surface to be covered.
Additional mortar is then applied with the notched edge of the trowel.
When installing large tiles, spread adhesive onto back of tile in addition to trowelling material over surface to be tiled. Select proper type of notched trowel.
a) Thin Tiles upto size 300 X 300 mm (1’X1’), use a square notched trowel of size 6mm X 6mm to provide a total thickness of 3mm
b) Large Porcelain Tiles upto 450 X 450 mm with ribs, use a square notched trowel of size 6mm X 6mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 4.5mm
c) Large Porcelain Tiles upto 600 X 600 mm (2’X2’) with ribs, use a square notched trowel of size 6mm X 9mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 6mm
The most important standard to keep in mind is to insure that the piece of tile is completely bedded in the mortar or adhesive with 100% coverage.
Rear face of tiles (especially Porcelain tiles) should be cleaned with damp sponge to clean all the dust. Do not saturate in water.
Excess mortar on adhesive shall be cleaned from the surface of the stone with wet cloth or sponge while the mortar is fresh.
Coverage Approx. 55-60 sq. ft. per 20 kg bag with a ¼” x ¼” (6mmx6mm) square notch trowel for a bed of 3mm. Color Grey
Areas of Application Designed for internal floor applications Suitable Substrates
Cement Mortar Beds
- Production Capacity: 300 MT PAR DAY
- Delivery Time: ORDER AFTER 2 DAYS
- Packaging Details: 20 KG AND 50 KG
|Minimum Order Quantity||50 Bag|
|Packaging Type||BOPP BAG|
|Pack Type||IS:-15477 TYPE 1 STANDARD|
|Packaging Size||20 kg,50kg|
|Model Name||IS:-15477 TYPE 1 STANDRD|
Virsun Sun Fix Floor Tile Adhesive is a bagged cementitious powder to be mixed with water for installing ceramic the and natural stone using the thin-set method of Installation. Tile adhesives are a factory prepared blend of carefully selected raw materials. Portland cement and graded aggregates (Latex) are added to adhesive powders to increase bond strength. Best suited for Exterior and Interior Installation of ceramic/ vitrified/ Porcelain/Engineered stones and Natural Stones.
Best suited for Exterior and Interior installation of ceramic/ vitrified/ Porcelain /Engineered stones and Natural Stones.
Single component, ready to use
High strength formula & ultimate flexibility
Ideal for external facades and underwater application
Cernen1 Mortar Bed
Single component, ready to use
Proven performance. I want buy tile adhesive
- Production Capacity: 300 PAR DAY
- Delivery Time: SAME DAY
- Packaging Details: 20 KG 50 KG